|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
more progress on the fabric work. covered the other elevator and did more tape and reinforcement patching. but the slit i cut for the control horn opened more when I shrunk the fabric. I patched it but undecided if I want to leave it or start over. There is another reinforcement patch that goes over that area and a tape so it may not be too bad, but it is on the top of the elevator (of course) What would you all do?
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
I went ahead and put the tapes and patches on. It isn't too bad, I really wish it had been on the bottom instead of the top though. But it is an amateur fabric job and since it is my first attempt at doing it it isn't half bad looking. I may leave it for now and see how much fabric and ecobond I have left when the job is complete do decide if i want to redo it or not.
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
I worked on getting the right aileron prepped for fabric
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
Braved the heat and put the fabric on my right aileron. That was harder then I thought it would be, but I think it will turn out ok after it is shrunk and the tapes are put on.
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
I shrunk the fabric on my aileron and did some of the tapes, It isn't perfect but certainly airworthy and I think when all the reinforcement patches and tapes are on it should look pretty good.
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
The tapes are finished on the ailerons and they are ready for painting now. next up I will try to tackle one of the wings.
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
been working off and on at getting a wing covered. I used the method from the Stewart systems youtube page and put felt on the leading edge then covered the bottom. It still has some ironing to do on it.
|
|
|
|
|
Cy V |
|
Ace
Posts: 641
Time Online: 14 days 16 hours 49 minutes
|
What is the purpose of the felt? Do you glue the felt on? |
| Bad spellers of the world untie! |
|
Logged |
Online |
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
the felt is glued on with spay glue then the ecobond is used to fix it permently |
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
I did another ironing then flipped the wing over to prep the top side for fabric
|
|
|
|
|
cdlwingnut |
September 12, 2020, 1:35am |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
The ailerons are attached and I got fabric on the top of the wing today
|
|
|
|
|
aeronut |
September 12, 2020, 3:27pm |
|
blue sky and tail winds to everyone Ace
Posts: 1,560
Time Online: 28 days 22 hours 31 minutes
|
May the force be with you. The iron is magic in it's ability to create a work of art; like a sculpture's chisel or a painters brush. Your airplane will be a work of art. |
| never surrender; never give-up |
|
|
|
|
cdlwingnut |
September 15, 2020, 1:49am |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
did the first pass of the iron on the top of the wing and it's not looking bad.
|
|
|
|
|
PUFF |
September 15, 2020, 11:42am |
|
Ace
Posts: 1,518
Time Online: 34 days 6 hours 18 minutes
|
|
|
|
|
cdlwingnut |
November 14, 2020, 1:18am |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
Haven't had much to report. I've been doing a few small things here and there. got the center section of the wing ready for fabric
|
|
|
|
|
aeronut |
November 14, 2020, 12:38pm |
|
blue sky and tail winds to everyone Ace
Posts: 1,560
Time Online: 28 days 22 hours 31 minutes
|
Your making progress on the airplane and that is what counts. Best wishes. |
| never surrender; never give-up |
|
|
|
|
cdlwingnut |
November 26, 2020, 5:16pm |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
spent the morning yesterday putting the fabric on the bottom of the center section wing. It's ready for the iron now
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
fabric is still going on slowly. The top of the center section now has skin. I just hope I didn't forget to do anything important in there.
|
|
|
|
|
streffpilot |
|
Flight Leader
Posts: 130
Time Online: 2 days 11 hours 14 minutes
|
so....when my 1550V is ready for fabric, you can come over to my house and help me, right?
Looking good! |
|
|
|
|
Cy V |
December 11, 2020, 10:01pm |
|
Ace
Posts: 641
Time Online: 14 days 16 hours 49 minutes
|
How many hours do you have in this build so far? |
| Bad spellers of the world untie! |
|
Logged |
Online |
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
Cy V, I hate to say it but i have no idea how many hours so far, I was really good at keeping track at first but then not so much.
I have been working on the rib stitching on the wings, getting the hang of it
|
|
|
|
|
cdlwingnut |
February 25, 2021, 1:37am |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
still rib stitching, haven't had a lot of time for building lately but did get the top of the wing stitched.
|
|
|
|
|
cdlwingnut |
February 27, 2021, 2:46am |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
took a little mental health time in the shop today and put the tapes on the top of the wing over the rib stitching. felt like it was kind of a shame to cover the wood with fabric and now to cover all the stitch work with the tapes.
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
It was time to flip the wing over and do the rib stitching on the bottom. I had to use a curved needle on every other rib due to the way the wing was braced so couldn't get a long needle all the way through the wing. I got the ribs stitched and some of the tapes on. One wing very close to being ready for paint.
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
finally finished the tapes on the left wing, and did the center wing section. Now the left wing and center wing part is ready for paint. This thing might fly yet.
|
|
|
|
|
aeronut |
|
blue sky and tail winds to everyone Ace
Posts: 1,560
Time Online: 28 days 22 hours 31 minutes
|
You could make it by this summer and I hope you do. In this world of instant gratification building an airplane does not qualify . Keep your eye on the prize and you will put air under those wheels. |
| never surrender; never give-up |
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
I really hope so aeronut. How rewarding would a nice late summer evening fight be in the little piet? You've probably wondered why the wheels were off the last few photos. I decided the axle was a bit too short and that the brake drums would end up cutting the bungee cords. So I ordered a longer tube to add a few inches to each side. Not only will this give me more clearance for the brake drums but probably give a little bit better ground handling. I also got a few little odds and ends done as well. |
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
More plugging away. The right aileron is hung on the wing now. I fabricated a few metal parts and put a coat of paint on them.
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
getting too low on the echo bond glue to start the top fabric of the right wing. So while waiting for an order of it I made a trip to sherwin williams for some paint. After testing it on some scrap fabric I felt brave enough to brush a coat on the vertical fin. I plan to brush the first coat on to get it into the fabric then spray the second and if needed the third coat on.
|
|
|
|
|
cdlwingnut |
|
Ace
Posts: 416
Time Online: 3 days 22 hours 22 minutes
|
did some wet sanding today then got the elevators primed.
|
|
|
|
|